Retatrutide issues

Omxxl

Omxxl

New member
Joined
Aug 19, 2026
Messages
61
Reaction score
0
Location
Imported archive
Hi there,

I’ve reconstituted two 30mg Reta vials—the ones with this specific label and purple cap—and the solution looks cloudy compared to the 20mg one in the photo. I ordered another 30mg kit in the same shipment; that one had the exact same cap and label, and I didn't have any issues with it.

Has anyone else experienced something similar? The bacteriostatic water is new, and it’s the same water I used to reconstitute my HGH and the other Reta vial.

If it’s cloudy, it’s not safe to inject, right?

Please help.
 
Hospira BAC or vendor? Ideally the peps are higher quality but cause it's not fully controllable, the main thing to keep consistent is your BAC quality so sticking with Hospira.
 
Just my 2c. I aint pinning anything that is cloudy even if it clears the next day. Most peptides clear within minutes. Grey is already risky, I aint taking additional risk. Its not like we're spending thousands on a single vial.

Best bet is too eliminate the BAC factor and get a hospira and try it out if its cloudy with Hospira too. But then again some kits are hit or miss, You might have 1 kit where 5 reconstitutes fine and 5 thats cloudy even with hospira. I dealt with this with the transparent blue cap R10. Some would recon fine and some would not but I did notice that the chances of it getting cloudy is higher with vendor BAC.
 
It’s BAC water from the same source as the peptide itself; I’ve reconstituted other peptides with it and had zero issues. It’s hard to get Hospira here in Europe.
 
My understanding is if it's cloudy, the the molecules are clumping together. The risk of injecting it goes beyond it being ineffective, there can be immune/allergic/antibody reactions. If it clears up it might be salvageable, but if it gets gel like or has floaties, toss for sure. The nacl is a good catch mentioned above, or possibly the pH of your bac isn't in range. Was the bac water cold when you mixed it? Low temp can make it harder for the powder to mix
 
faloppi said:


My understanding is if it's cloudy, the the molecules are clumping together. The risk of injecting it goes beyond it being ineffective, there can be immune/allergic/antibody reactions. If it clears up it might be salvageable, but if it gets gel like or has floaties, toss for sure. The nacl is a good catch mentioned above, or possibly the pH of your bac isn't in range. Was the bac water cold when you mixed it? Low temp can make it harder for the powder to mix

Click to expand...
Click to expand...
Yes, the water was cold, but the second vial wasn't quite as cold.
 
Omxxl said:


It’s BAC water from the same source as the peptide itself; I’ve reconstituted other peptides with it and had zero issues. It’s hard to get Hospira here in Europe.

Click to expand...
Click to expand...
you have cheap pH test strips by chance? if the bac water is a little out of range, it might work for some more forgiving peptides but not be good for the reta (or this batch anyway)

Omxxl said:


Yes, the water was cold, but the second vial wasn't quite as cold.

Click to expand...
Click to expand...
if it was just the temp, after 30mins on the counter, and a little swirling, it should clear up
 
Omxxl said:


Hi there,

I’ve reconstituted two 30mg Reta vials—the ones with this specific label and purple cap—and the solution looks cloudy compared to the 20mg one in the photo. I ordered another 30mg kit in the same shipment; that one had the exact same cap and label, and I didn't have any issues with it.

Has anyone else experienced something similar? The bacteriostatic water is new, and it’s the same water I used to reconstitute my HGH and the other Reta vial.

If it’s cloudy, it’s not safe to inject, right?

Please help.

Click to expand...
Click to expand...
Let us know if it clears up please.
 
Just had this happen to me too. Been buying for 3 years and have never had a cloudy vial. I wonder if it is a manufacturer issue.
 
quicksilver80 said:


Ive noticed if i reconstituted with a small 31g needle and push too fast it can cloud up for a very short time. Dont know if thats a possibility

Click to expand...
Click to expand...
That's a pretty small gauge needle to be reconing with.
 
BNLFL said:


That's a pretty small gauge needle to be reconing with.

Click to expand...
Click to expand...
Have you seen the price of sharps boxes? 😛

Kidding aside, I recon most of mine with the 31g, they work for Tirz

I guess Reta is a little more sensitive to the "jet" action, but if you aim at side you are likely ok
 
Back
Top